AISI M2 high speed tool steel manufacturers and suppliers, supplied in round bar,square bar,flat bar,plate,sheet and wire.M2 is a molybdenum high speed steel,as a standard, it is most widely used industrial HSS.It has small and evenly distributed carbides giving high wear resistance, though its decarburization sensitivity is a little bit high.M2 has superior properties in toughness, wear
M2 high speed tool steel is tungsten-molybdenum high-speed steel with a well-balanced carbon composition and high toughness. It is also called JIS SKH51 and DIN 1.3343 steel. It is easy to overheat, control the quenching heating temperature is necessary ASTM A653 DX51D hot rolled steel coil - Boiler and 60 - 275g /m2 Galvanized Steel Coil ASTM A653 / SGCC ASTM A653 DX51D hot rolled steel coil. 60 - 275g /m2 Galvanized Steel Coil ASTM A653 / SGCC / DX51D EN, JIS, GB Standard . Description Hot-dipped galvanized steel sheet is characterized by protection base metal(Fe)
ASTM M2 Data Table for Steel Grades :ASTM M2 Mech ASTM M2 - Manusteelcn-China steel suppliersASTM M2 Data Table for Steel Grades :ASTM M2 Mech
DENSITY OF STEEL. The density of steel is in the range of 7.75 and 8.05 g/cm 3 (7750 and 8050 kg/m 3 or 0.280 and 0.291 lb/in 3).The theoretical density of mild steel (low-carbon steel) is about 7.87 g/cm 3 (0.284 lb/in 3).. Density of carbon steels, alloy steels, tool steels and stainless steels are shown below in g/cm 3, kg/m 3 and lb/in 3. Grade M2 Tool Steel McMaster-CarrChoose from over 500 grade M2 tool steel products in a wide range of sizes. Includes material certificates and CAD models. In stock and ready to ship.
ASTM M2 high speed tool steel annealing is recommended before Re-hardening. Heating the M2 high speed tool steel to 850°C , The rate of less than 220°C per hour. Keep at temperature for 1 hour per inch(25.4mm) of thickness (with 2 hours being Min). Cool slowly in High Speed Steel Tool Steel Compare Tool SteelSome, most notably M2 and powder metal M4, are used in cold work applications because of the strength and wear resistance which can be achieved. To qualify as a high-speed steel, the chemical composition must meet certain minimum requirements, which are defined in the ASTM A600 Specification for High-Speed Tool Steels.
M42 High-Speed Tool Steel. M42 is a cobalt-molybdenum super high speed steel that is known for its superior red-hardness in comparison to M2 steel. The addition of cobalt to the composition of M42 provides a good balance of toughness and hardness. M42 high speed steel M2 Tool Steel SKH51 W6Mo5Cr4V2 1.3343 High Speed Supply Form of HSS M2 Tool Steel -ASTM A681 High Speed Steel. Round Square sheet Plate Supply Range of SAE M2 Tool Steel HSS. M2 Steel Round Bar:diameter 1mm 400mm. M2 Steel Plate:thickness 1 500mm x width 200 1400mm. M2 Steel Block:210mm x 500-810mm.
References Cast irom, ASTM A48, structural steel fro bridges and structures, ASTM A7. Structural rivet steel , ASTM A141; high-strength structural rivet steel, ASTM A195 . Conversions. 1 Pa (N/m 2) = 1x10-6 N/mm 2 = 1.4504x10-4 psi 1 MPa = 10 6 N/m 2 = 0.145x10 3 psi (lb f /in 2) = 0.145 New ASPN High Efficiency Treatment of ASTM M2 Steelthe results of the tests performed with ASTM M2 steel. ASTM M2 was used in this work as there are several papers concerning the nitriding of this material. ASTM M2 is a high speed steel used in the manufacturing of cutting and forming tools, and has a good response to plasma nitriding, reaching high wear resistance values, very important for use
781M, ASTM A 703/A 703M, ASTM A 957, ASTM A 985, and ISO 4990. ASTM A 781/A 781M 16 CASTINGS, STEEL AND ALLOY, COMMON REQUIREMENTS, FOR GENERAL INDUSTRIAL USE This specification covers a group of requirements that are mandatory requirements of the following steel casting specifications issued by American Society of Testing Stainless Steel Equivalent Grades, Stainless Steel stainless steel 1.4571 equivalent, stainless steel 1.4408 equivalent, stainless steel 1.4301 equivalent, stainless steel 1.4541 equivalent, stainless steel 1.4310 equivalent, stainless steel 1.4462 equivalent, stainless steel 310 equivalent, stainless steel aisi 316l equivalent, stainless steel aisi 316 equivalent
m2 skh51 1 3343 high speed steel for mould material price. Standard:ASTM, ASME, AISI, GB, JIS, DIN, EN, BS Certification:ISO, SGS, RoHS, CE, IBR Production Capacity:50000 tons Per Month Description:AISI M2 Steel - JIS SKH51 - DIN 1.3343 - Songshun SteelM2 high speed tool steel is tungsten-molybdenum high-speed steel with a well-balanced carbon composition and high toughness.ASTM A600 Grade Type M2 (high C) Cold Drawn - Tool And See the chemical composition and physical properties of ASTM A600 Grade Type M2 (high C) Cold Drawn, find alternative materials, and connect with suppliers. ASTM A53 Carbon Steel Pipes. ASTM A564 Stainless Steel Age Hardened. Alloy Steel:Properties, Processing and Applications.